Nxg-technology NX-82C Manuel d'utilisateur télécharger pdf

NX-52C, NX-62C, NX-82C Ceiling-Mount Speaker System

Where To Place Your In-Ceiling Speakers

Placement can make all the difference in how your speakers sound, and how easy they will be

to install. Carefully consider where your speakers should be positioned. For optimum perform-

ance, speakers should be mounted to the left and right of the main listening area and a minimum

of 8 to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical

wiring, heating ducts, water pipes, etc. Make sure the ceiling materials are sturdy enough to

support the weight of the speakers.

Adjustable Tweeters (Fig. 3)

The tweeter in your NXG speaker may be adjusted, allowing you to tailor the speaker to better

fit the listening area. The overall smoothest response is achieved with the tweeter facing

straight out: however, you may find the sound more pleasing by aiming tweeters toward a

particular listening area. To adjust the tweeter, apply pressure on the ring surrounding the

tweeter with your thumb or finger.

Speaker Installation In Existing Construction (See Fig. 4 on reverse)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers • Speaker Wire

• Pencil • Phillips Screwdriver • Utility Knife or Drywall Saw • Masking Tape

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer

or custom audio contractor.

1. NXG Architectural Speakers are designed to be installed in the ceiling or wall area between

studs. Using a stud finder, make sure you are between two studs. Tape the supplied template

to the wall and lightly trace around the inside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of

the outline. This will allow you to check for any obstructions that may exist behind the desired

location. CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfer

e in

the planned installation areas prior to drilling or cutting the wall.

3. Run speaker wir

e fr

om your amplifier or speaker switching device to the speaker location.

4. Carefully remove the grille and inner grille backing. (Note: The open cell foam inner grille

backing is designed to hide speaker components from view and may be removed if desired.) If

you like the standard white finish of your NXG speakers, skip to step 5, but if if you want your

speakers to blend in with a colored wall or ceiling, now is the time to paint your speaker’s outer

frame and perforated grille. (Remove the foam inner grille backing and put it aside in a clean and

dust free area for later reinstallation if desired.) The speaker’s outer surface will accept ordinary

latex wall paint or aerosol spray paint. Because the speaker baffle surface behind the grille should

remain unpainted, you will need to cover this ar

ea with the supplied car

dboar

d paint mask. Cover

the speaker’s interior black surface, woofer and tweeter. Paint the outer speaker frame and grille

separately. (Grille painting hint: Use a paint roller that is nearly out of paint to first paint the inside

of the grille, then the outside. This will avoid paint filling the grille perforations.)

5. Attach the wire to the input terminals on the rear of the speaker. Remember to maintain

proper polarity with the amplifier by attaching the positive (+) lead to the r

ed ter

minal and the

negative (-) lead to the black terminal.

Congratulations on choosing NXG In-Ceiling

Loudspeakers. Like all NXG products, great

care has been taken in their design. Their

combination of advanced engineering and

state-of-the-art materials will provide you

with years of listening pleasure, while blending

smoothly into your home’s decor. Before you

get started, it is a good idea to identify all the

parts and hardware (See Fig. 1).

FIG. 1

Mounting Template Speaker with self-contained

mounting clamps

Metal Grille

FIG. 2

NXG ceiling speakers can be used as rear

surround channels by mounting them (1)

on each side of, (2) just behind, or (3) in

back of the viewing position.

FIG. 3

Press on

the edge of

the tweeter

to rotate

OWNER’S MANUAL

Black grille

adhesive

(Continued on r

everse)

1 2

Résumé du contenu

Page 1 - OWNER’S MANUAL

NX-52C, NX-62C, NX-82C Ceiling-Mount Speaker SystemWhere To Place Your In-Ceiling SpeakersPlacement can make all the difference in how your speakers s

Page 2 - Operational Check

Warranty ServiceWarranty service must be performed by an authorized service center, usually a NXG speaker systems dealer or its authorizedagent. You m

Modèles reliés NX-62C | NX-52C |

Commentaires sur ces manuels

Pas de commentaire

Nxg-technology NX-82C Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Acoustique Nxg-technology NX-82C. NXG Technology NX-82C User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés NX-62C | NX-52C |

Commentaires sur ces manuels

Produits connexes et manuels pour Acoustique Nxg-technology NX-82C