Nxg-technology NX-W8.3-P Manuel d'utilisateur télécharger pdf

(Continued on reverse)

Where To Place Your In-Wall Speakers

Placement can make all the difference in how your speakers sound, and how easy they will

be to install. Carefully consider where your speakers should be positioned. For optimum per-

formance, speakers should be mounted to the left and right of the main listening position and

a minimum of 8 to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities con-

taining electrical wiring, heating ducts, water pipes, etc. Make sure the wall or ceiling mate-

rials are sturdy enough to support the weight of the speakers.

In-W

all Placement:

Optimum performance will be achieved when your speakers are mounted

at ear level or slightly higher. If you desire to mount them higher in the wall, turn the speaker

over so the tweeter is closer to the listening area.

In-Ceiling Placement: Optimum performance will be achieved when your speakers are

mounted to the left and right of the main listing area.

Pivoting Tweeter & Midrange (Fig. 3)

The tweeter and midrange in the NX-W8.3-P speakers may be adjusted, allowing you to tailor

the speaker to better fit the listening area. The overall smoothest response is achieved with the

tweeter and midrange facing straight out: however, you may find the sound more pleasing by

aiming them toward a particular listening area. To adjust the tweeter or midrange, apply pres-

sure on the ring surrounding the unit with your thumb or finger

Tweeter/Midrange Level Adjustments (Fig. 3)

The level switches allow you to tailor the speakers’ frequency response to better match the

room’s acoustics. As an example, if a room has a hardwood floor, which makes it acoustically

brighter sounding, you may want to adjust the tweeter and midrange levels to compensate. You

can experiment with both levels to find the sound that’s most pleasing to you in your partic

ular listening environment.

Speaker Installation In Existing Construction (See Fig. 4 on reverse)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder

• Drill & Drill Bits • Wire Cutter/Strippers

• Pencil • Utility Knife or Drywall Saw • Small Level

• Masking Tape • Phillips Screwdriver • Speaker Wire

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer

or custom audio contractor.

1. NXG Architectural Speakers are designed to be installed in the wall area between studs.

Using a stud finder, make sure you are between two studs. Using the supplied template and

a level to ensure your template is straight, trace around the outside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center

of the outline. This will allow you to check for any obstructions that may exist behind the

desired location. CAUTION: Be certain electrical wiring, water pipes or heating ducts do not

interfere in the planned installation areas prior to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. Carefully remove the grille and inner grille backing. (Note:

The open cell foam inner grille

backing is designed to hide speaker components from view and may be removed if desired.) If

you like the standard white finish of your NXG speakers, skip to step 5, but if if you want your

speakers to blend in with a colored wall or ceiling, now is the time to paint your speaker’s outer

Congratulations on choosing NXG

In-Wall Loudspeakers. Like all NXG

products, great care has been taken

in their design. Their combination of

advanced engineering and state-of-

the-art materials will provide you

with years of listening pleasure,

while blending smoothly into your

home’s decor. Before you get start-

ed, it is a good idea to identify all the

parts and hardware (See Fig. 1).

FIG. 3

Press on the edge of the

tweeter or midrange to rotate

FIG. 2

NXG Pro Series In-Wall Speakers can be used as

rear surround sound channels by placing them

(1) behind, (2) on each side of viewer, or (3) in the

ceiling just behind viewing position. They also make

excellent front channel home theater speakers (4).

Adjust

tweeter &

midrange

levels by

setting

switches

NX-W8.3-P Three-Way In-Wall Speaker System

FIG. 1

Metal grille w/foam

inner grille cover

peaker w/ self-contained

mounting clamps

Black

rille

adhesive

ainting mask

Cutout template

Grille

removal

ool

Tweeter

level switch

Midrange

level switch

R Sensor

Knockout

1 2

Résumé du contenu

Page 1

(Continued on reverse)Where To Place Your In-Wall SpeakersPlacement can make all the difference in how your speakers sound, and how easy they willbe t

Page 2 - Operational Check

Warranty ServiceWarranty service must be performed by an authorized service center, usually an NXG speaker systemsdealer or its authorized agent. You

Commentaires sur ces manuels

Pas de commentaire

Nxg-technology NX-W8.3-P Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Acoustique Nxg-technology NX-W8.3-P. NXG Technology NX-W8.3-P User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Acoustique Nxg-technology NX-W8.3-P