(Continued on reverse)
Where To Place Your Ceiling Speakers
Placement can make all the dif
ference in how your speaker will sound, and how easy it will be
to install. Carefully consider where your speaker should be positioned. For optimum perform-
ance, the speaker should be mounted as close as possible to the center of the main listening area
(See Fig. 2). Avoid mounting the speaker in stud cavities containing electrical wiring, heating
ducts, water pipes, etc. Make sure the wall or ceiling materials are sturdy enough to support the
weight of the speaker.
Adjustable T
weeter
(Fig. 3)
The tweeter in the NXG Model NX-522DVC may be adjusted, allowing you to tailor the speaker to
better fit the listening area. The overall smoothest response is achieved with the tweeter facing
straight out: however, when the speaker cannot be mounted in an optimal location, you may
find the sound more pleasing by aiming the tweeter toward a particular listening area. To adjust
the tweeter, apply pressure on the ring surrounding the tweeter with your thumb or finger.
Speaker Installation In Existing Construction (See Fig. 4 on reverse)
Once you have selected the location for your speakers, you are ready to install them.
You will need the following:
• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers
• Pencil
• Utility Knife or Drywall Saw • Small Level
• Masking Tape • Phillips Screwdriver • Speaker Wire
NXG r
ecommends the use of a minimum of 16-gauge wire. For wire options consult your retailer
or custom audio contractor.
1. NXG Architectural Speakers are designed to be installed in the wall or ceiling area between
studs. Using a stud finder, make sure you are between two studs. Using the supplied template,
tape the template to the ceiling and lightly trace around the inside with a pencil.
2. Cut the hole using your dr
ywall saw
. You may want to start with a small hole in the center of
the outline. This will allow you to check for any obstructions that may exist behind the desired
location. CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in
the planned installation areas prior to drilling or cutting the wall.
3. Run speaker wir
e fr
om your amplifier
, volume contr
ol or speaker switching device to the
speaker location.
4. Remove the grille from the speaker. If you like the standar
d white finish of your NXG Ceiling
Speakers, skip to step 5, but if if you want your speakers to blend in with a color
ed wall, now is
the time to paint your speaker’s outer frame and perforated grille. The speaker’s outer surface
will accept ordinary latex wall paint or aerosol spray paint. Because the surface behind the grille
should remain unpainted, you will need to cover this ar
ea. Cover the speaker
’
s interior black
surface, woofer and tweeter. Paint the outer speaker frame and grille separately.
5. Attach the wire to the input terminals (right and left) on the rear of the speaker. Remember
to maintain proper polarity with the amplifier by attaching the positive (+) lead to the red termi-
nal and the negative (-) lead to the black ter
minal.
Congratulations on choosing NXG In-Wall Loudspeakers.
Like all NXG products, great care has been taken in their
design. Their combination of advanced engineering and
state-of-the-art materials will provide you with years of
listening pleasure, while blending smoothly into your
home’s decor. Before you get started, it is a good idea
to identify all the parts and hardware (See Fig. 1).
FIG. 1
Mounting Template Speaker with self-contained
mounting clamps
Grille
FIG. 2
FIG. 3
Press on
the edge of
the tweeter
to rotate
NX-522DVC Dual Voice Coil Ceiling-Mount Speaker System
OWNER’S MANUAL
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels